Design of Erickson Over-The-Cab Truck Bed Ladder Rack

Question

Question:

The rack pictured on the blue Chevrolet looks completely different than the rack in the other pictures. Has the design changed? What is the current design?

asked by: Bryan H

0

Expert Reply:

I verified with Erickson that the design of the ladder rack # EM07707 has never changed from the original. The picture and video I've linked shows the actual design.

expert reply by: Charles S

0

click to enlarge

Answer 1

The Erickson Over-The-Cab Truck Bed Ladder Rack #EM07707 referenced in your question is confirmed to fit your 2007 Dodge Ram 3500 Megacab and is a great product that will provide you with 800 pounds of weight capacity. The rear bar of the ladder…

view full answer...

Answer 2

Looks like you'd be good. I pulled up the towing capacity of your truck and it's rated for 15,350 lbs trailer weight and your trailer would weigh at most 12,995 lbs. The M5 Series hitch part #RP30928 that you referenced has a 20k…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

I have a solution for you Travis as Pace Edwards does not offer a contractor rack for your 2023 GMC Sierra 1500. Instead you can use the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover #311-M-FMCA28A59 with the Thule TracRac SR…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 8

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 9

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 10

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 11

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...