Male and Female Pipe Mounts for etrailer Square Pipe Mount Swivel Jack TJDP-7000S-B

Question

Question:

What pipe mounts both male and female do you have that would be compatible with this jack as far as hole diameter and hole back set. I would like to install 2inch male and/or 2 1/2inch female mounts on several trailers so that I can use the jack on various trailers? This jack comes standard with a 2 1/2 female mount so if I used a 2inch male mount would that reduce the weight capacity? Is there a standard way to attach the jack and trailer pipes together...ie trailer pipe into jack pipe vs jack pipe into trailer pipe? Thanks

asked by: Rich

1

Helpful Expert Reply:

The end that normally attaches to jack # TJDP-7000S-B is # TJP-OP58. It has an outer diameter of 2-1/2 inches and inner diameter of 2 inches.

For a weld-on male end that has 5/8 inch pin holes to match the above female mount use # BD015279.

expert reply by: Michael H

1

Answer 1

Sealant is not required when installing a grease seal, like #RG06-050 you referenced. The cap will not need a sealant either. See the help article I've attached that explains the entire process of replacing bearings, races, and seals. I've…

view full answer...

Answer 2

The Replacement Mounting Hardware part #LC701665 comes with the Extension Rods, Extension Rod Bracket, Torsion Arm Caps, and various hardware. I am not sure what all you have now but it sounds like you might also need the torsion heads, part #LC87FR…

view full answer...

Answer 3

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 4

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

Answer 5

The #37213635 JR Products Replacement Landing Gear Switch you'd mentioned would be a proper replacement for your existing Atwood 70254 landing gear switch. If you wanted the switch, wiring harness and the bezel for the switch, use the Stromberg…

view full answer...

Answer 6

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

If your trailer has separate turn signals from the brake lights and you want them to remain that way, you will need to use a special converter. On the trailer side, behind the 7-Way, you will attach the Vehicle to Vehicle Taillight Converter,…

view full answer...

Answer 9

The easiest way to cut the oval hole for the Rubber Grommet, #a70gb, in my opinion, would be to use a Light Mounting Bracket for 6-1/2 inch Oval Trailer Lights, BK70BB, as a template and then use a hole saw the correct size to cut a hole on each end…

view full answer...

Answer 10

I have a solution for you, but we do not have any replacement lights that will fit in those grommets. Instead, you can use the LED Clearance or Side Marker Light #MCL002AXB (amber) and #MCL002RXB, which require a rough cutout dimension of…

view full answer...

Male and Female Pipe Mounts for etrailer Square Pipe Mount Swivel Jack TJDP-7000S-B

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching