Step Height of TorkLift GlowStep Revolution RV Scissor Steps

Question

Question:

Hello, What is the vertical distance between steps on the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear - 4 Steps - 27-7/16inch Base - 350 lbs? Also, what is the vertical distance from the top step to the entry door? Thanks.

asked by: Richard B

0

Expert Reply:

From the mounting surface of where the Torklift Steps part # TLA8004 attaches down to the first step measures 3 inches in the highest setting. There is also a 3 way adjustment you can make for the position of the step that will change that distance. Highest is 3 inches, middle is 5 inches, and lowest is 7 inches.

The distance between each step is 7-1/2 inches.

expert reply by: Charles S

0

Answer 1

These are great steps, no negative concerns with the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear. However, #TLA8004 that you linked to is designed for an entry height of 32-1/2" - 44". If you have an entry height of…

view full answer...

Answer 2

The TorkLift GlowStep Revolution Scissor Steps #TLA8004 that you referenced are designed to fit the standard RV step areas with the bracket kit part #TLA8022. There will most likely be some drilling though since these do install in a slightly…

view full answer...

Answer 3

For lubricating RV folding steps like your Torklift Glowsteps part #TLA8004 the best lube is a dry silicone lube like the part #RM-747 since it won't attract dirt and road grime like most lubes would.

view full answer...

Answer 4

I spoke with my contact at Torklift and he informed me that from the mounting surface of where the Torklift Steps part #TLA8004 attaches down to the first step measures 3 inches in the highest setting. He also said that there is a 3 way adjustment…

view full answer...

Answer 5

Hey Beatrice, To find the right fit for your trailer's suspension you'll need to take a quick measurement of your current shackle straps. You'll need to measure from the center of one bolt hole to the center of the other bolt hole. The…

view full answer...

Answer 6

Hey Dave, the MORryde upgraded shackle kit part #MR76ZR that you referenced is compatible with your 2020 Grand Design 2670MK and the Lippert Road Armor equalizers.

view full answer...

Answer 7

Hey Tom so I definitely know what you are asking for but due to the very minimalistic design of the Kuat Transfer part #KU84FR there isn't a great way to add lights to it. But the good news is that you most likely don't need additional…

view full answer...

Answer 8

Thanks for the axle information, Mike! Here are the correct parts according to my contact at Curt: - Bearing #02475 and Race #02420 - Bearing #25580 and Race #25520 - Grease Seals #RG06-070

view full answer...

Answer 9

There are differences in them but we do have what you are looking for and they can in some situations be used together. The Replacement Trailer Hub Bearing you have part #02475 and Replacement Race for 02475 Bearing part #02420 are designed to work…

view full answer...

Answer 10

The TorkLift GlowStep Revolution Scissor Steps #TLA8004 are a possible fit for your 2016 Dutchmen Voltage 3914. These steps are designed to work with a entry height measurement of 13-7/8 inches to 32-1/2 inches measured from the ground to the floor…

view full answer...

Answer 11

When replacing steps on a 5th wheel trailer you will want to stay with the same number of steps unless going to more steps retains the same retracted dimensions of your existing steps. For aftermarket steps there is no fit information in regards to…

view full answer...

Answer 12

I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7843 away from your camper to clear your bumper. It may be possible to have a…

view full answer...

Step Height of TorkLift GlowStep Revolution RV Scissor Steps

Product Page this Question was Asked From

Continue Researching