Trailer Hitch that Could Fit Jayco Trailer Frame

Question

Question:

I have a 2015 Jayco trailer and I wanted to put a hitch on the rear that mounts to the frame. Is there a particular model where the bolts will line up?

asked by: Trevor S

0

Expert Reply:

We don't have a custom fit trailer hitch for your Jayco trailer but the Curt hitch part # 13703 will be your best option. It fits trailer frames that are between 22 and 72 inches in width and can fit box frame, C-channel frame, or I-beam frames.

I attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

For your 2017 Jayco Jay Flight SLX 267BHSW travel trailer, I recommend the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403. This is a very nice weld on option adjustable from 47-1/8 to 77 inches. For a bolt on option, I…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 5

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 8

The TireMinder i10 TPMS #TM38FR refreshes every 6 seconds which would be the quickest option we have. I would agree that the 5 minute refresh rate of the #TST-507-FT-4-C is really long.

view full answer...

Answer 9

To convert your axle for a top mounted leaf spring I would recommend replacing the U bolts, nuts and tie plates, so your best bet would be to go with a U bolt kit. For a 2-3/8" round axle use #APUBR-1 For a 3" round axle use #APUBR-9 You…

view full answer...

Answer 10

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 11

The best way to measure a trailer spring for purposes of selecting a replacement is to remove it completely from the suspension. It is also important to note that leaf springs will tend to elongate over time as they wear. You might pull a well-worn…

view full answer...

Answer 12

You will have to do some measuring. Take a look at our Double-Eye Trailer Suspension article (see link). I have also linked a picture of a shackle link showing where to measure. Measurements for replacement 1) Measure current shackle from center of…

view full answer...