Weld on Trailer Jack with Wheel That Swivels Up

Question

Question:

Does this jack fit a 2015, tail motorcycle trailer? Would you have one with wheels?

asked by: Mark

0

Expert Reply:

The jack you referenced can basically fit any trailer design as it is a weld-on application so it should be a great option for you. It doesn't have a wheel though so a weld on jack part # FXP15W might be a better option as it does come with a wheel.

expert reply by: Jameson C

0

Answer 1

We do offer both swivel jacks and replacement parts like wheel assemblies. Sometimes a non-original replacement wheel assembly can be used, even one from another brand. The linked page displays the replacement wheels and replacement caster/wheel…

view full answer...

Answer 2

For your swivel jack, I recommend the Bulldog Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs #BD151443. This will give you the ability to use a caster wheel like #BD500245. For a footplate you can use #BD018564. These…

view full answer...

Answer 3

The foot on the inner tube on Pro Series trailer jack #PS1401480303 is attached, all one part, so you would not be able to add a wheel. None of the pipe-mount swivel jacks come with a wheel. Your best option would be to replace the jack with…

view full answer...

Answer 4

There are not any caster wheels that we carry that are rated for that 5,000 lb capacity. My recommendation for a durable wheel is the Replacement 6" Caster Wheel #BD500245. This is rated for 1,200 lbs and is the strongest caster we carry that…

view full answer...

Answer 5

It's odd, but you are correct there isn't a trailer jack we offer that matches all of the criteria you need for your trailer. You'd have to compromise with a jack like the #BD158452 that doesn't have the wheel or with something like…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Weld on Trailer Jack with Wheel That Swivels Up

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching