Will The Tensioner For Bulldog Winches Work On A Smittybilt 9500 XRC Winch?

Question

Question:

Will the work on a smittybilt 9500 xrc winch

asked by: Tony

1

Helpful Expert Reply:

The Tensioner for Bulldog Winch Standard Series Truck Winch - Wire Rope, # BDW20234, is a confirmed fit for all Bulldog standard series truck winches. However, it is compatible with many other winches. Although I can't confirm the fit on your specific winch, I have attached a picture with measurements in millimeters for you to check mounting compatibility.

expert reply by: Jason S

1

click to enlarge

Answer 1

The Tensioner for Bulldog Winch Standard Series Truck Winch - Wire Rope #BDW20234 or the ComeUp Cable Tensioner for DV-12, DV-15, and DV-18 winches #CU881087 are the only options for that size a winch. We have not tested them on a Smittybilt x20…

view full answer...

Answer 2

See the attached photos. The first photo shows the mounting bolts, which are 10” apart, center to center. The second photo is the roller, which is 8” in width. The last photo shows the roller bracket, which is 7.25” in width.

view full answer...

Answer 3

It sounds like there is a short circuit that is overloading the running light circuit in the tow package wiring on your tow vehicle. The most likely culprit is a dirty or corroded trailer connector on the vehicle or trailer if not both. The first…

view full answer...

Answer 4

I spoke with my contact at Bulldog Winch and he informed me that the overall length of the #BDW20234 measures 8-1/2 inches. I attached a picture that shows all of the other dimensions of it in millimeters for you to check out as well.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Yes, because it is a 3-wire light, you can wire the Red Identification Light Bar with White LED Utility Light #OPT88FR to function as rear marker and reverse lights.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Will The Tensioner For Bulldog Winches Work On A Smittybilt 9500 XRC Winch?

Product Page this Question was Asked From

Continue Researching