Overall Length of the Tensioner for Bulldog Winch Standard Series Truck Winch BDW20234

Question

Question:

What is the length of this tensioner?

asked by: Derrick

0

Expert Reply:

I spoke with my contact at Bulldog Winch and he informed me that the overall length of the # BDW20234 measures 8-1/2 inches.

I attached a picture that shows all of the other dimensions of it in millimeters for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Bulldog Universal mounting plate #BDW20291 has overall dimensions of 7-3/8 by 20 inches. The plate is 1/4 inch thick and the fairlead portion sits up about 4-1/2 inches according to my contact at Bulldog. The holes for the fairlead are 10…

view full answer...

Answer 2

Easiest way will be to use the winch plate mount part #BDW20291 that you mentioned but attach it to the floor of the trailer at the very front to a crossmember of the frame. To mount in the V area of the A-frame is possible but it would require…

view full answer...

Answer 3

The Tensioner for Bulldog Winch Standard Series Truck Winch #BDW20234 will help in evenly putting the cable on but you would still want to watch it and make sure it is spooling up the right way.

view full answer...

Answer 4

We have never tested the ComeUp cable tensioner part #CU881087 on the Superwinch LP 10,000 but I have attached the bolt hole measurements of the tensioner. It installs above the drum of the winch. You may be able to attach it to the Superwinch.

view full answer...

Answer 5

The Tensioner for Bulldog Winch Standard Series Truck Winch part #BDW20234 is designed specifically for Bulldog Standard Series Winches part #BDW10041 for 8K, part #BDW10042 for 9.5K, or part #BDW10043 for 12K. Therefore, I cannot confirm it will…

view full answer...

Answer 6

The roller on the Tensioner for Bulldog Winch #BDW34QR is 1" in diameter and 8-1/2" long.

view full answer...

Answer 7

The Tensioner for Bulldog Winch Standard Series Truck Winch - Wire Rope, #BDW20234, is a confirmed fit for all Bulldog standard series truck winches. However, it is compatible with many other winches. Although I can't confirm the fit on…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Overall Length of the Tensioner for Bulldog Winch Standard Series Truck Winch BDW20234

Product Page this Question was Asked From

Continue Researching