Recommendation for an Amber LED Clearance Light That Will Work on a 24-Volt System

Question

Question:

Do you have any Led rectangular clearance lights in amber that are rated at 24V system?

asked by: Darin G

0

Expert Reply:

Yes, we carry the Optronics Thin-Line LED Amber Clearance Light # MCL66A24B. This light will work with both 24 and 12-volt systems.

expert reply by: Jared P

0

Answer 1

There is a lot of confusion when folks say submersible or waterproof. The difference is that submersible lights will have a small hole that allows the water to drain out if the light has been submersed in water. Waterproof is a sealed light that will…

view full answer...

Answer 2

I went out to the warehouse and pulled the Waterproof, Under 80 inch LED Trailer Light Kit, item #TLL9RK, to see exactly what Optronics means by waterproof. Upon initial inspection the housing itself is not water tight. Water can access the housing…

view full answer...

Answer 3

One main difference between LED lights and incandescents is the amount of power each one draws. I did a little research and found that if you were to have LEDs and incandescents on the same circuit, it would be too much power draw for the LEDs…

view full answer...

Answer 4

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 5

The Superwinch Winch 2 Go 4000 SR #SW1140232 includes a mounting plate that bolts to the bottom of the winch's main housing. This yellow steel plate itself has four exposed mounting holes to allow it to be secured to a stationary surface. The…

view full answer...

Answer 6

Looking at the numbers on your axle we aren't going to have an exact replacement. Looks like you need a 4,400 lb axle with most likely a hub face to face dimension of 97 inches and spring seat to seat dimension of 70 inches if I am reading your…

view full answer...

Answer 7

Check and clean the connectors of the 7-way on your vehicle. Typically when a brake controller like the P3 Brake Controller part #90195 doesn't want to go into sleep mode it is because the controller is falsely detecting a trailer due to…

view full answer...

Answer 8

The Dexter 8-133 axle according to my contact at Dexter is an old motorhome axle they no longer make. Their tech said the motorhome axles like what you have are designed for one time use so there are not compatible parts made for even replacement…

view full answer...

Answer 9

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 10

I do have a really similar option that will work great, however the Optronics Thinline LED Utility Light #UCL59CB that you referenced can't be used as a backup light on your trailer. This is simply because the light doesn't meet DOT…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

I'll start out by saying that you don't necessarily have to use the same sized lights, but it's occasionally helpful when it comes to mounting them. However, if you're not replacing like for like, the odds that your new lights will…

view full answer...

Recommendation for an Amber LED Clearance Light That Will Work on a 24-Volt System

Product Page this Question was Asked From

Continue Researching