Which Circuit Breaker to Install with Prodigy Brake Controller for Use with 3-Axle Trailer

Question

Question:

I intend to usually haul a 1-2 axle trailer, but would like to be able to hook up to a 3 axle without replacing the circuit breaker. Should I install the 20amp or 30 amp circuit breaker from the ETBC7 kit?

asked by: Andrew Z

0

Expert Reply:

You will want to use the 30-amp breaker when you install your # ETBC7 Brake controller kit. This will pass enough current for the Prodigy controller # 90195 to power up to 6 brake assemblies on three axles. The 40-amp breaker should be installed on the 12V trailer power circuit.

expert reply by: Adam R

0

Answer 1

While I can sympathize with your issue, it is not safe to tow a trailer if you only have a 2" hitch ball and your trailer coupler is designed for a 2-5/16" hitch ball, even for a short distance; the insecure connection between hitch ball…

view full answer...

Answer 2

That will depend on the amount of brake axles your trailer has. . The 20 amp breaker like #9506P is for 1 and 2 axle brakes, and the 30 amp like part #38630 is for 3 and 4 axle brakes

view full answer...

Answer 3

You'd want to use the 20 amp circuit breaker like #PK54220PL unless your trailer has more than two brake axles. If that's the case you'd want to use the 30 amp breaker #38630.

view full answer...

Answer 4

To answer your first question, it is possible to splice the brake controller's 12 volt power wire into the 12 volt power wire you have attached to the vehicle's battery to charge the trailer's battery but this is certainly not recommend.…

view full answer...

Answer 5

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 6

I think you are going in the right direction. I would definitely replace the 14 gauge wire going to the trailer brake magnets with 10 gauge wire or larger. Usually larger than 10 gauge is hard to get into the trailer connector though. I would also…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Which Circuit Breaker to Install with Prodigy Brake Controller for Use with 3-Axle Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching