How Does B and W Headache Rack part # BWPUCP7500BA Install On a Vehicle

Question

Question:

how does this headache rack attach to the truck

asked by: Jerry

0

Expert Reply:

I attached the installation instructions for the B and W Headache Rack part # BWPUCP7500BA that you referenced. Basically you attach a set of brackets to the bed rail and then attach the rack to the brackets.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We offer one headache rack that fits your 2014 Ford F-250 which has lights, which is made by B&W. There is not a separate splitter for this headache rack or other racks, it does require you to splice into your wiring, as you can see from the cut…

view full answer...

Answer 2

The height of the B&W Custom Headache Rack #BWPUCP7500BA has a height of 24-3/8 inches. You'd want to measure from the top of your bed rails to the top of the truck cab to see if it would be taller than it or not.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 12

If you're wanting to add a 4-way to power your trailer's signal lights then you need the Curt #CU94FR. If you want to add a 7-way to your 2024 Santa Cruz then you can use the Curt #C68JR. Both of these plug into the tow package you referenced…

view full answer...

How Does B and W Headache Rack part # BWPUCP7500BA Install On a Vehicle

Product Page this Question was Asked From

Continue Researching