Recommended Replacement License Plate Light

Question

Question:

I have a 1992 pro craft boat trailer need replacement license light. original bulb number asael 2059 75w.

asked by: Carl B

0

Expert Reply:

We don't have an exact replacement for that license plate bulb. I recommend replacing the entire unit with the Peterson License Plate Light with Bracket, # PM436B. The internal parts are all stainless steel or brass to extend the life of this unit. I've attached a video for you.

expert reply by: Jason S

0

Answer 1

Thank you for your recent purchases from etrailer. A bad or insufficient ground is among the most common causes for issues with trailer lighting. The Peterson License Plate Light #PM436B that you have does use its steel mounting surface to make the…

view full answer...

Answer 2

The Peterson License Plate Light w/ Steel Mounting Bracket #PM436B grounds through it's mounting hardware so the single wire is the power wire for the light (attaches to running light circuit).

view full answer...

Answer 3

When wiring a 2-wire license plate bracket, such as the Optronics LED #LPL55CB, you are correct that the white wire will be for ground and the black wire is used for the running lights. The white wire from the bracket should be attached to a clean,…

view full answer...

Answer 4

Your old light must be a model that grounds through the mounting hardware. The new light has a separate ground wire. The white wire is the ground and it will attach to a clean metal surface. The black wire is the power wire.

view full answer...

Answer 5

In regards to the Optronics LED Trailer License Plate Light part #LPL55CB, the black wire is for power and the white wire is a ground. The black wire will be hooked up to the running light circuit which is usually a brown wire. If you have a ground…

view full answer...

Answer 6

You will need to use a quick splice, item #SWC502905-1, and splice the black wire from the LED Trailer License-Plate Light, item #LPL55CB, into the taillight wire on your trailer. The taillight wire is normally the brown wire, but you should use a…

view full answer...

Answer 7

Run the white wire on your trailer to the mounting bolt of the new license plate light. Your current light ground through the mounting hardware so you'd just need to connect the ground wire there and you'd be good.

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Recommended Replacement License Plate Light

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching