Will A Hitch Receiver Off A 1996 Ford Ranger Work On My 1985 Ford Ranger?
Question:
I have a hitch receiver on a 1996 ranger I want to put on my 1985 ranger, will it work?
asked by: Dan
Expert Reply:
If you have the Curt Class III Receiver Hitch, # 13019, then the hitch receiver is a confirmed fit for both year models of Ford Ranger trucks. If you have a different model of hitch receiver, it may or may not be compatible. There are models of hitch receivers from the same company that are not compatible between these two year models.
To add a ball mount for towing, I suggest the Curt Ball Mount for 2 Inch Hitches With 1 Inch Rise and 2-1/4 Inch Drop, # C45030. You'll also want a 2 inch hitch ball like Tow Ready's # 63845 or a 2-5/16 Inch ball like # 63847. You will also need the Pin and Clip for your receiver like # C21500.
To add wiring to your 1985 Ford Ranger, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Connector, # 118313. This is a harness that will simply plug into existing wiring with no splicing required. The plug is located beneath your vehicle along the drives-side frame near the rear bumper. I'd recommend adding a mount like # 18144 to keep the connection secure.
Products Referenced in This Question
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
2-5/16" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-3/16" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 3-3/16 Inch Span
- CURT
more information >
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Does Draw-Tite Trailer Hitch 13091 Require Drilling to Install on 2001 Ford Ranger
- Article: Trailer Tire Sizing
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Recommended Trailer Hitch Receiver for 2004 Ford Ranger Edge
- Q&A: Trailer Hitch for 2008 Ford Ranger that Allows Full Size Spare
- Q&A: Recommended Trailer hitch Receiver For a 2008 Ford Ranger 4x4
- Q&A: Does the etrailer Hitch item # e29AR Work w/ a Full Size Spare Tire on a 2005 Ford Ranger?
- Q&A: Comparing the Curt Round Hitch 13138 and Curt Square Hitch 13019 for a 1992 Ford Ranger
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: My Trailer Hitch Doesn't Fit
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Install a Weight Distribution Hitch (With Pictures & Video)
- Article: Which Hitches are Made in the USA
- Article: Trailer Wiring Diagrams