Will Husqvarna BT150 Blower Back Fit on Blower Rack for Utility Trailer RA-19

Question

Question:

Hi, will the Husqvarna BT150 Backpack blower fit this?

asked by: Sid A

1

Helpful Expert Reply:

Yes, I looked up pictures of the Husqvarna BT150 and it's handle design and location on top of the blower pack makes it compatible with the Lockable Blower Rack for Utility Trailers # RA-19.

expert reply by: Jameson C

1

Answer 1

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 2

I pulled from our warehouse a piece of Titan Trailer Hub Assembly for 2,000-lb Axles #T4084600042 so that I could measure it for you. I have linked a photo of this 5-on-4-1/2 bolt pattern hub with various dimensions noted, including overall length…

view full answer...

Answer 3

For their Lockable Blower Rack #RA-19, Rack'em notes that Stihl blower models BR420, BR550 and BR600 will require an adapter but this requirement does not apply to the RedMax EBZ8500 blower.

view full answer...

Answer 4

Since your Carry-On 5' x 8' Utility Trailer has a 2000lb GVWR it more than likely has a 2000lb axle and would need a hub that uses either inner and outer bearings #L44643 or #L44649. I know on The 5' x 8' Carry-On Trailer I bought…

view full answer...

Answer 5

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…

view full answer...

Answer 6

The diameter of the pilot hole for the Americana Steel Trailer Wheel, part #AM20026 is 2.81-inches. You would have to make sure your trailer hub measures that dimension or less to fit inside the pilot hole. This wheel rim measures 8-inches diameter…

view full answer...

Answer 7

BTR and BT8 are the reference numbers for a standard trailer spindle size. When picking out a hub for a trailer you have to make sure that the hub is designed to fit the spindle. What you will need to do is measure spindles on your trailer where the…

view full answer...

Answer 8

I called Titan about the Titan Trailer Hub Assembly, part #T4084600042, and to get some of the dimensions you need. I have attached a photo that has the dimensions noted. The outside diameter of the hub is 5.69 inches and the outside diameter of the…

view full answer...

Answer 9

A 20.5x8.5-10 is going to be about 2 inches taller than the 18.5 tires you have now. If there is enough space above the existing tires to go to the taller size then you can use them. I have included some links on tires for you as well.

view full answer...

Answer 10

In order to account for the new tire and wheel size, you will want to take a few measurements. A 16.5 x 6.5 - 8 wheel is 5.3" wide with an overall height of 16.5". A 18.5 x 8.5 - 8 wheel is 7" wide with an overall height of 18.3".…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Will Husqvarna BT150 Blower Back Fit on Blower Rack for Utility Trailer RA-19

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching