What Size Channel Does the Trailer Coupler CTA-280 Fit

Question

Question:

Can you tell me the measurements at the back of the hitch crazy-280?

asked by: Neal M

0

Expert Reply:

Sounds like you are trying to determine what the # CTA-280 would fit. It was designed to fit 3 inch channel like the part # CTA-CB126. The distance between the mounting holes is 2 inch on center and the hole diameters are 5/16 inch.

I attached a review video on this for you to check out as well.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hi Mark; thanks for the question and I have some good news for you as we have the exact 5th wheel to gooseneck adapter to replace the Turning Point pin box on your Jayco Eagle HT 30.5 CKTS. The correct part is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hey Trevor, so the B and W Companion Slider hitch part #BWRVK3400 only fits the B and W Turnoverball gooseneck hitches and would not fit the gooseneck hitch of your 2022 Chevy Silverado 2500 with OEM pucks. The funny thing about the Patriot slider is…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

There might be a solution but it all comes down to what gooseneck hitch you have installed in your truck. If you can let me know what brand hitch you have I can help find you exactly what type of slider hitch solution would work best. Hopefully you…

view full answer...

Answer 9

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...