Will the Phoenix USA QuickTrim Hub Cover # PXQT655WHN Fit EZ Lube Spindle Hub

Question

Question:

Will this Cap fit over Dexter E-Z Lub Axle Hubs?

asked by: Bill

0

Expert Reply:

Yes, the Phoenix USA QuickTrim Hub Cover # PXQT655WHN would have enough clearance to fit over the zerk fitting of an EZ lube spindle.

expert reply by: Jameson C

0

Answer 1

Yes, the Dexter axle part #8327816 that you referenced has the exact same spindle as a Lippert 5,200 lb axle so the hubs and bearings would interchange.

view full answer...

Answer 2

The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast you're traveling, and also driving habits. So while 158 is probably…

view full answer...

Answer 3

Yes, you can paint the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #PXQT655WHN. I contacted the manufacturer to verify this. They said you would just need to sand them down a little and then paint them.

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Will the Phoenix USA QuickTrim Hub Cover # PXQT655WHN Fit EZ Lube Spindle Hub

Product Page this Question was Asked From

Continue Researching