Availability of Bow Roller Kit that Includes End Bow Bells

Question

Question:

Do these Bow Bell come in pairs or individually if I am buying the bow roller

asked by: Carlos

0

Expert Reply:

The Yates Bow Bell # YR400BLK that you referenced comes individually in that part number.

For a kit that includes the 4 Inch roller, 2 end bells, and corrosion-resistant hardware, you will want the Yates Bow Roller Assembly with Bells for 4 Inch Wide Bracket # YR450BLK-400BLK. This kit includes the TPR roller and end bells.

expert reply by: Victoria B

0

Answer 1

Looks like you have the part #YR450BLK-400BLK installed and are needing the next size down which happens to be the part #YR300BLK-325BLK. This fits the same 1/2 inch diameter shaft but is 1 inch shorter than what you have. Your bell ends being…

view full answer...

Answer 2

You could definitely replace the bow roller on the front of your Boatmate trailer with a Yates Y-Style Bow Stop for Boat Trailers #YR6Y33-4 as long as the mounting hole dimensions will match up to your boat roller. This stop is designed to fit a 1/2…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Availability of Bow Roller Kit that Includes End Bow Bells

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching