Will Yakima Replacement Rack and Roll Wheels Fit Rack and Roll Trailer from Before Buyout

Question

Question:

My 2006 trailer was made by the Rack and Roll company of San Luis Obispo, CA which Yakima has since purchased. It looks like the one pictured on your site but Id like to be sure these wheels will fit. Mine has 3-spoke wheels with tire size 3.50x18. My trailer Thanks!

asked by: Craig P

0

Expert Reply:

I spoke with my contact at Yakima and she told me that if the wheels you have were 5-spoke then the part # 8880157 that you referenced would fit as a replacement. Since what you have is a 3 spoke then this wouldn't work and there really isn't a solution besides replacing enough of the trailer that it would be just as easy to replace the whole thing.

expert reply by: Jameson C

0

Answer 1

According to Yakima, the Heavy Duty Shocks for Yakima Rack and Roll Trailer #Y08110 should only be used if you add the 78" crossmember kit #Y08111. They didn't have an exact reason for this, but it sounds like the concern is people will…

view full answer...

Answer 2

The tire on the Yakima Rack and Roll trailers is a 3.25-16, which is an uncommon size for a trailer. The company that makes the tire is called FEICHI TYRE. They make a lot of motorcycle tires. I went out and inspected our Yakima Rack and Roll trailer…

view full answer...

Answer 3

I checked with Yakima and they told me to have to have you clean and lubricate the bushing and then try to pull it off with a pair of pliers. Force isn’t an issue because if they can’t get the bushing off we will need to replace the trailer side…

view full answer...

Answer 4

I went out to the warehouse and pulled a spare tire and wheel for Yakima Rack and Roll trailers #Y08121. I used digital dial calipers and measures the inner diameter of the bearings and it came to 0.581 inches. I also made a short video showing this…

view full answer...

Answer 5

The Replacement Axle Bolt Kit for Yakima Rack and Roll Trailers #Y8880180 measures 9" long total and measures 7-7/16" from the bottom of the bolt head to top of the threads. It is also 14mm (0.55") in diameter. I have attached a…

view full answer...

Answer 6

Since we have started carrying the Yakima Rack and Roll trailer #Y08107 I have not heard any complaints regarding the wheel bearings failing and only a few instances where people wanted to replace the wheel assembly. If you need to replace your…

view full answer...

Answer 7

view full answer...

Answer 8

The tires for the Yakima Rack and Roll Trailer like the Replacement Tire for Wheel on Yakima Rack and Roll Trailers #Y8880282 are rated for 94 mph, although to be honest I'm not sure that's a speed I'd be comfortable testing...

view full answer...

Answer 9

I went out into our warehouse and grabbed a Replacement Axle Bolt Kit for Yakima Rack and Roll Trailers #Y8880180 to measure the dimensions of the head of the bolt and the nut. You would need to use a 7/8 inch wrench or socket on either end.

view full answer...

Answer 10

I contacted the manufacturer about replacing the 3.25"-16" tires on your Yakima Rack and Roll Trailer with 3.50"-16" tires. They recommend that you continue to use the Replacement Tire for Wheel on Yakima Rack and Roll Trailers…

view full answer...

Answer 11

We do have replacement axle bolt and nut kits for the Rack and Roll trailers like #Y08107 with the part #Y8880180.

view full answer...

Answer 12

I went out to the warehouse and pulled Replacement Axle Bolt Kit #Y8880180 to measure the cotter pin in the kit. The pin is approximately 0.11 inches thick whereas the hole is just slightly larger than 0.125 inches (1/8). The pin has an overall…

view full answer...

Will Yakima Replacement Rack and Roll Wheels Fit Rack and Roll Trailer from Before Buyout

Product Page this Question was Asked From

Continue Researching