Will the Curt Hitch # 13456 fit a 2011 Land Rover Range Rover Sport Super Charged with a 19 Spare
Question:
Will part #13456 Curt Receiver hitch fit on a 2011 RR sport super charged edition with a 19inch spare?
asked by: Mike K
Expert Reply:
I contacted my tech contact at Curt and unfortunately the Curt Hitch for a 2011 Land Rover Range Rover Sport # 13456 will not work on your vehicle with a full size spare tire. However, if you remove the tire, this hitch will work with your super charged edition.
If you plan on doing some towing with your vehicle, I recommend adding a ball mount, hitch ball, and trailer wiring. The recommended ball mount is # 2753, and you can use hitch ball # 19260 (1-7/8 inch diameter) or # 63853 (2-5/16 inch diameter).
For wiring, you will need to use the 4 Pole Harness and Hardwire Kit, # C59496.
I attached an installation video for the Curt Hitch on a 2010 Land Rover Range Rover Sport which is the same process for your 2011 Land Rover you may find helpful. I also attached a review video on the wiring harness you may want to check out.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
2-5/16" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Stainless Steel - 6,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2-5/16 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 6000 lbs GTW
- Class III
- Draw-Tite
more information >
Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 8 Feet Long
- Universal Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 6000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 800 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Q&A: Is a 10 PSI Increase in Trailer Tire Pressure Normal from Heat Created by Driving
- Article: Trailer Maintenance Schedule
- Q&A: How to Determine Correct Rise or Drop for Blue Ox SwayPro Weight Distribution System
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Q&A: How to Reset Zero Point Calibration on Lippert Ground Control 3.0
- Q&A: LCI Leveling System Troubleshooting
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: How To Install HBA-CAM Hydrastar Adapter
- Article: How to Choose the Right Trailer Hitch Class
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Electric Brake Controller Installation on Dodge Ram Trucks to 2012
- Article: Best Bike Racks for Electric Bikes
- Article: My Trailer Hitch Doesn't Fit