Should Trailer Leaf Springs be Replaced in Pairs

Question

Question:

if you have one bad leaf spring should you replace both?

asked by: Miles

0

Expert Reply:

When in comes to replacing leaf springs on trailers we recommend that you replace them in pairs so you are using the same springs on each side of the axle.

I attached a help article on trailer suspension leaf springs for you to check out as well.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on…

view full answer...

Answer 3

Thanks for the photos, and from that it looks to me like you are asking if just the pitch arm assembly is available, and if so, the answer is yes, it is the Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm…

view full answer...

Answer 4

Thank you for the image of the axle tag for your Dexter D80 8,000LB axle. This will require the 10-36 Grease Seals #RG06-070 you found. Here is a list of the other components your axle uses should you want to replace or find any parts worn. Inner…

view full answer...

Answer 5

For your Dometic RM2652 fridge we do not have a cover that fits the 21-1/2" x 4-1/4" screw holes you are looking for. The RV Refrigerator Roof Vent Cap and Base #DMC37FR (#DMC97FR for black) has screw hole measurements of 22" x…

view full answer...

Answer 6

Okay, we can get you all of that, and let's start with the equalizer upgrade, suspension kit, and shocks for your toy hauler with triple 8,000 lb axles. The best equalizer upgrade for your 35 inch axle spacing, along with the needed suspension…

view full answer...

Answer 7

Yes, the Dexter trailer leaf springs like the part #DX74XR are made in the USA.

view full answer...

Answer 8

According to the installation instructions from Dexter Axle the torque specs for the wet bolts on their Dexter E-Z Flex Suspension Kits, like part #K71-653-00, is 30 - 50 ft-lbs. I have attached a clip from their instructions for you to check out.

view full answer...

Answer 9

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Answer 10

The shorter shackle straps that measure 2-5/8 inches long like part #115052GALV are typically used on dual or triple axle systems. The tandem axle hanger kit part #APT3 which includes 7-3/4 inch equalizers uses 2-5/8 inch shackles.

view full answer...

Answer 11

Between the two kits, the better option for replacing your 2-5/8" shackle straps is the version with the shorter 2-1/4" shackle straps, which is the following part number: - MORryde Suspension Upgrade Kit for Tandem Axle Trailers #MR46ZR…

view full answer...

Answer 12

I attached a picture that shows the proper position of shackles and equalizers on trailer suspension. Sometimes the shackle will flip up but if you jack up the trailer by the axle that's got the shackle flipped you can usually get it to flip back…

view full answer...

Should Trailer Leaf Springs be Replaced in Pairs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching