Height of the Back Section on the Bestop TrailMax II High Back Seat B3943615

Question

Question:

Is the back of the seat higher than the original seat in a 1982 CJ-7? Not counting the headrest

asked by: Tracy

0

Expert Reply:

The back section of the Bestop TrailMax II High Back Seat you mentioned, part # B3943615 that you referenced measures 22-1/2 inches without the headrests.

With the headrests all the way up the overall height is 31 inches, with them pushed down as far as they will go it measures 28 inches.

You would have to compare that dimension to the height of your current seat to know if this would be taller or not.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I spoke with my contact at Bestop who gave me the following dimensions for the Bestop TrailMax II Fold & Tumble #B3943915: Base: Length - 40-1/2" Depth - 20" Cushion Thickness - 5-1/4" Backrest: Indented Length - 30" (longer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

What you need is a light kit specifically for flat-towing. The Plug-N-Tow TM Vehicle Wiring Harness, #42615, would be if the Jeep were towing a trailer and not for activating its lights while it is being towed. There are a few options for lighting…

view full answer...

Answer 4

The Hopkins Adapter 7-Pole to 6-Pole #47549 plugs into a vehicle side 7-way socket and converts that connector format to a 6-way round-pin type. If you think you will need some length for your connection, #HM47083 is an alternative that does the same…

view full answer...

Answer 5

I went out to the warehouse and measured seat #B3944137 which fits a CJ models from 1955 to 1995. These dimensions will be the same or nearly identical for all Jeep seat options. The seat portion of the seat is approximatel7 17 inches from the front…

view full answer...

Answer 6

Thank you for the photos of your 2006 Honda Pilot, but the center bolts are still needed to install the etrailer Trailer Hitch Receiver #e98851. What you will need to do - if you can - is drill the holes in the bumper beam, though I can't quite…

view full answer...

Answer 7

In order to take the old Thule #TH145148 fit kit off of your Evo Clamp Feet for Thule Crossbars - Naked Roofs - Qty 4 #TH710501, you'll need the hex tool that came with the Evo feet; you'll want to unscrew the internal bolt using that tool…

view full answer...

Answer 8

I went ahead and got those dimensions for you from our warehouse. The Bestop TrailMax II Fold & Tumble - Vinyl Rear Bench #B3944015 measures 33-1/4" wide x 19" deep x 30-3/4" tall (with the headrests extended to the maximum). The…

view full answer...

Answer 9

I reached out to my rep at Curt and was able to get a couple of options for you. Both of these are going to require some modifications because there is no custom fit front hitch available for your 2012 Chevy Express 2500 Cutaway Van. Your best bet is…

view full answer...

Answer 10

I've put together a photo for you showing the dimensions of the #e98975 etrailer Replacement Tow Bar Adapter Kit for Roadmaster Direct-Connect Base Plates. I've also linked to a product description video for the adapter kit.

view full answer...

Height of the Back Section on the Bestop TrailMax II High Back Seat B3943615

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching