Replacement Cover for Jensen Z26 AS 13 Roof Vent

Question

Question:

I have a Jensen Z26 AS 13 white roof vent cover I would like to replace . It measures 13 1/4inch from outside lip to outside lip and has three hinge bars. Would you have a replacement for this model?

asked by: Keven N

0

Expert Reply:

If your old vent cover was held on by a pin, we have some replacement vent lids that would work great for you. For white, use part # CAM40154 or for smoke colored, use # CAM40147.

expert reply by: Mike L

0

Answer 1

If your trailer camper has an Elixir roof vent with a continuous hinge the part #CAM40155 that you referenced would be a correct fit for it.

view full answer...

Answer 2

Unfortunately, there are 4 styles of replacement lids, so you will need to look at the hinges of your 1991 Fleetwood Flair. I've attached a photo of the hinge options for you to choose from and then you will just need to determine the opening…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 7

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 8

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 9

I'm not quite sure what you mean by the "heart", however for your Ventline VD0434 we have the replacement screen frame #BVA0444-32, the replacement screen #BVD0434-31, the replacement lid #BVD0449-A01, and the replacement ceiling…

view full answer...

Answer 10

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Answer 11

The 15,000 Btu Furrion air conditioner is what I would recommend and what I have on my trailer. Since it is an enclosed trailer I'm guessing you want the manual distribution box. You can choose from the following based on color: -Furrion Chill HE…

view full answer...

Answer 12

To determine the correct cover, you will need to measure the vent opening. The most common openings are 14 1/4" x 14 1/4", and have vents that are 14" x 14". After you make your measurements, you will need to determine what type…

view full answer...

Replacement Cover for Jensen Z26 AS 13 Roof Vent

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching