Air Bag Kit Recommendation for Front Axle of 2000 Workhorse P30 Chassis

Question

Question:

Is this tbe correct application to replace the airbags inside the springs on the front of my motorhome? I also need rear sway bar bushings for my 11/2inch sway bar. Do you have them?

asked by: Craig S

0

Expert Reply:

The Air Lift Kit part # AL81560 that you referenced is the correct air bag kit for the front springs of your 2000 Workhorse P30 chassis that your Itasca Sunrise is built on. You would need to remove what is there now and install these in place of them.

I wish we had the bushing you need, but at this time we do not have stock sway bar bushings for RVs like yours.

expert reply by: Jameson C

0

Answer 1

I don't have a way to look up your axle based on the number you gave me but I can help you pick out the correct replacement axle based on a few measurements. First thing you need is the axle capacity. That would be listed on the axle on a…

view full answer...

Answer 2

The only option we carry for front suspension for your 2003 Winnebago Brave (Workhorse 32V) is the Air Lift 1000 Air Helper Springs for Coil Springs - Front #AL81560. The Air Lift 1000 provides 1,000 pounds of load-leveling capacity and has an…

view full answer...

Answer 3

For the RVP/Coleman AC Units like your 7000 the correct shroud is the part #MA8335A5261. I attached a Review video for this for you to check out as well.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 8

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

For your 2024 Nissan Frontier I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. I like the Liberty because it is simple, reliable, and looks great in any vehicle. The main unit installs behind the dash, so only the control knob will…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Yes, when installing the knob for the Redarc Tow-Pro Liberty Brake Controller item #RED24FR you will want to remove any extra material behind the insert. I am happy the video was able to help you out. I have linked a couple of pictures from the video…

view full answer...