Replacement Trim Rings for Ford OEM 5th Wheel Hitch

Question

Question:

Do you sell the o-rings separately?

asked by: Randy

0

Expert Reply:

Replacement Trim Rings for the Ford trucks with factory rail kit can be ordered as part # RP58458.
Part # 58199 that you referenced is a set of 2 rubber puck plug covers. We also offer a Puck Service Kit # 58253 that includes one each: puck, trim ring, lock washer and bolt.

expert reply by: Adam R

0

Answer 1

If all you need is covers for the Ford hitch prep package pucks that you have on your truck all you would need is the part #58199. If you need the trim rings you would want the part #RP58458 which comes with 4 rings. Unless you need the service kit…

view full answer...

Answer 2

The caps that you are looking for to cover the prep package holes in your 2020 Ford F-250 are the Replacement Puck Plug Covers #58199 for the 5th wheel plugs (they are sold in pairs, so you would need to purchase 2 to cover all 4 holes) and the…

view full answer...

Answer 3

The Blue Ox Aftermarket Off-Road Bumper Adapter #BX88357 has a maximum rating of 10,000lbs. You would also want to check with the bumper manufacturer and see what their weight rating for Dinghy towing would be. So they will not be strong enough for…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

I recommend using a Lube Plate #16721 over covering the Demco Recon 5th Wheel Trailer Hitch #DM8550043 in Grease #L74FR. The lube plate is much cleaner and you will not have to constantly clean off the dirt and apply new grease over time.

view full answer...

Answer 11

The best air bag kit for your 2020 Ford F-250 Super Duty with a single rear wheel are the Firestone Ride-Rite Air Helper Springs because they are the strongest, most durable air bags on the market to provide you with optimal support for your…

view full answer...

Answer 12

The pin weight of a 5th wheel trailer will usually be around 20% of the trailer's gross trailer weight (GTW) rating. The only real way to find the loaded pin weight of your 5th wheel trailer would require access to a commercial scale used to…

view full answer...

Replacement Trim Rings for Ford OEM 5th Wheel Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching