Installation Instructions for the Camco RV Insect Screens for Dometic Refrigerator Vents

Question

Question:

How do these vent screens attach to the fridge cover?

asked by: Eric V

1

Helpful Expert Reply:

I was able to go out to the warehouse and see that the Camco insect screens # CAM42149 include a small zip tie to attach the screen to your existing cover.

I have linked a few images of the instructions showing the installation process to this page for your convenience.

expert reply by: Jackie C

1

click to enlarge

Answer 1

The Dexter hub part number prefix 8-201 could refer to many items and includes many possible weight capacities. So the best way to go is to pull one hub, remove the bearings and find their stamped part numbers. If you happen to know the…

view full answer...

Answer 2

Yes, the Bearing Kit for #84 Spindles part #BK2-100 is correct for a 2018 Grand Design Imagine. This is actually the correct bearing kit for all sub models that use the "120091" 3,500 Lb Axle such as the 2800BH or 2600RB for…

view full answer...

Answer 3

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 10

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Installation Instructions for the Camco RV Insect Screens for Dometic Refrigerator Vents

Product Page this Question was Asked From

Continue Researching