Will the Hydraulic Line Kit 80910-T fit a 1995 Jayco Pop Up

Question

Question:

i have a 95foot jayco tent trailer. It looks like this is the right hose for my brakes.

asked by: Ilya

0

Expert Reply:

If you are in need of a flexible brake line that measures 13-3/4 inches the part # 80910-T would work well for you. This is normally used on Ltd Access Torsion Axles but it can be used on basically any setup where the length dimension matches and the fitting size is the same. This has a fitting size of 3/16"-20.

I attached a picture that shows it installed in a common application.

expert reply by: Jameson C

0

click to enlarge

Answer 1

First, on kit #80910-T, one end of the flexible hose attaches directly to the brake assembly. You will then route the other end to the steel brake line and use the metal piece with the flared ends to go from the flexible hose to the steel brake…

view full answer...

Answer 2

We do have one a-frame coupler, part #DM8609502 available and it is rated for 8,000 pounds, I think this would be the best fit for your trailer. The Titan coupler that you referenced is designed to bolt directly on a the trailer tongue. This is a…

view full answer...

Answer 3

Thanks for the picture of your actuator that you are wanting to replace. The Demco Hydraulic Actuator part #DM8609502 would be a great option as it is designed to fit A-frames like yours. It has an 8k capacity, designed for a 2 inch hitch ball, and…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Will the Hydraulic Line Kit 80910-T fit a 1995 Jayco Pop Up

Product Page this Question was Asked From

Continue Researching