Replacement Single Crossbar Recommendation for a TracRac Ladder Rack

Question

Question:

Hello, I have a 1997 Chevy C/K 1500 short bed. I have one damaged rail. Is it possible to order just one rail or do I have to order the set of two? Also, is the subject rail ok for my truck. Thank you,

asked by: Bob C

0

Expert Reply:

If you have a TracRac ladder rack installed on your 1997 Chevy Truck the correct part number for a single crossbar is the part # TAFX-30007-02 that you referenced.

This is 69-1/2 inches long and would be the correct length for your rack.

expert reply by: Jameson C

0

Answer 1

The Yakima ShowDown part #Y04081 can fit Thule crossbars but the rack can't fit on roof racks that use door jambs as the attachment. So if your 2014 Honda has flush mounted roof rack that your Thule rack attaches too the Yakima Showdown…

view full answer...

Answer 2

The Thule Hullavator #TH898 is designed to fit the same channel dimensions that your TracRac ladder rack has so there really isn't any reason the Hullavator couldn't fit the TracRac bars. TracRac is also made by Thule as well.

view full answer...

Answer 3

There is not a general restriction from Thule that says two Hullavator Kayak Carriers #TH898 can't be used on a Thule roof rack. As long as the crossbars on your Ford Escape have the required length for two sets and a sufficient weight capacity…

view full answer...

Answer 4

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 8

I'll start off with the ski rack for your 2024 Jeep Grand Cherokee Laredo since that is fairly simple. I recommend the Rhino-Rack Ski and Snowboard Carrier #RR574. This is capable of holding 4 pairs of skis, has an aluminum construction for…

view full answer...

Answer 9

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 10

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 11

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 12

The Thule Hullavator Pro, part #TH898, does in fact need crossbars that extend 4" - 8" beyond the feet. To use the flush rails on your 2021 Toyota RAV4, you will need a roof rack that has feet that are compatible with the rails. With those…

view full answer...

Replacement Single Crossbar Recommendation for a TracRac Ladder Rack

Product Page this Question was Asked From

Continue Researching