Equal-I-Zer Weight Distribution System without Shank and with 1,000 Pound Tongue Weight Capacity

Question

Question:

can I interchange the standard 7inch rise shank for one with a little more rise

asked by: Al G

0

Expert Reply:

We have a version of the Equal-I-zer 1,000 pound weight distribution system that does not come with a shank so that you can choose one that has the correct rise or drop needed to tow the trailer level. It is # EQ37101ET.

I have included a link to the compatible shanks for you.

expert reply by: Michael H

0

Answer 1

The Andersen Camper Leveler #AM3604 is designed to fit the majority of tandem-axle trailers, but according to my contact at Andersen Tools the leveler can be trimmed if necessary to allow use with closely-spaced axles. You would simply need to trim…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

To be completely honest the sway control feature of the B and W Continuum part #BW78FR isn't nearly as advanced as the rest of the system. The advertised sway control of this system is in the head of the system between where the ball and the…

view full answer...

Answer 5

Hey Paul, I spoke with Curt and they stated that the Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System #C17535 would only be compatible with the #C17499. The Curt TruTrack 4P Trailer Mounted Weight Distribution System w/…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It does appear you are going to be able to flip the axles on your 2023 Northern Spirit 2145RBX using 2 of the Dexter Trailer Springs Over-Under Conversion Kits #K71-384-00. I will warn you Kalvin this will raise the height of your camper roughly…

view full answer...

Answer 8

Thanks for the pictures! No, I am sorry Richard you can not. The B&W Continuum item #BW78FR only works with frames that are 5" and 6" tall. Instead, I recommend using the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control…

view full answer...

Answer 9

Thanks so much for that info it was really helpful, and we do have the right Equal-i-zer weight distribution hitch for your trailer with 850 lbs of tongue weight; the correct part is the following: - Equal-i-zer Weight Distribution System #EQ37100ET…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The Equal-I-zer, #EQ37100ET, and Reese Strait-Line, #RP66084, weight distribution systems are both top notch systems that will get the job done for you, but I usually tend to lean towards the Equal-I-zer systems for a few reasons. First, Equal-I-zer…

view full answer...

Answer 12

The Equal-i-zer Weight Distribution System #EQ37100ET that you referenced has a shipping weight of 109 lbs so it is a little hefty like the majority of WD systems out there. If you take away a few pounds for the shipping materials you are left with…

view full answer...