Bolster Brackets and Swivel Assemblies for SeaDoo Trailer

Question

Question:

I have a seadoo trailer that needs 13 inch bolsters but I have 2X4 carpeted bunks, so I need swivels that will fit the bunks with 1 1/2 inch bolt spacing. Do you have swivels that will fit a 2X4 bunk??? Thank you very much.

asked by: Joe A

0

Expert Reply:

I can help you find the correct bolster and swivel brackets for your Seadoo trailer.

The CE Smith part # CE10002G is a galvanized 13 inch bolster with a swivel bracket assembly. The swivel bracket will fit your 2 x 4 bunk great, but the brackets included have a 2-1/2 inch center spacing. We do offer a swivel bracket with a 2 inch center spacing # CE10206AA, but with either I would recommend drilling a hole in the bracket where you need it.

It's important to keep in mind that its a good idea to not reuse the old holes when replacing the bunk to the bracket, instead it is recommended to use a new location to get a better hold.

If you needed u-bolts to complete your setup part # CE15283GA measures 3-13/16 inches long x 3-1/16 inches wide and has a 1/2 inch diameter.

expert reply by: Jackie C

0

Answer 1

For roller bunks for your Sea Doo trailer you will want to first determine how long of bunks you would need. For a 5 foot long section the part #DL21741 would be a great option. I attached a picture of what they look like installed. Or for a 4 foot…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Bolster Brackets and Swivel Assemblies for SeaDoo Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching