Do the DeeZee Rough Steps # DZ15321A-15336 Require Drilling for Install

Question

Question:

Does the mount kit bolt to the factory holes/mounts or is there drilling required?

asked by: R H

1

Helpful Expert Reply:

I checked the install instructions for the DeeZee Rough Steps # DZ15321A-15336 for your 2013 Ram 2500 and there is no drilling required. Basically you install crimp nuts in the truck frame to provide attachment points for the mounting brackets. I attached a picture that I took from the install instructions.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 12

The Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A93VR is designed to fit the youru 2022 Ram 3500 with a 8' dually bed. The Cover #A37FR will only fit an 8' bed with single rear wheels. This is the only difference in these covers is…

view full answer...

Do the DeeZee Rough Steps # DZ15321A-15336 Require Drilling for Install

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching