Lower Gutter Foot Clamp for 2011 Chevy Express Van

Question

Question:

I have a 2011 chevrolet express, no existing rails or crossbars, I would like to know if the gutter clamp foot comes in a lower high other than 7inch if so please let me know before I place the order. Part # INB165,INSD

asked by: Edwin

0

Expert Reply:

I can help you find a lower gutter mounted roof option for your vehicle.

The # INLD is a 5-1/2 inch tall gutter mount and is a lower option than the # INSD which is 7-1/2 inches in height. The good news is the # INLD is a custom fit for your 2011 Chevrolet Express Van, so if you use the # INLD with the # INB165 rails you will have the lower setup you are looking for.

expert reply by: Jackie C

0

Answer 1

The Inno Feet for Square Crossbars #INSD referenced in your question are designed to attach to factory rain gutters like what it sounds like you have on your RV. Installing these feet along with a pair of square crossbars like the 71 inch #IN434…

view full answer...

Answer 2

We don't have a way to determine that from here since we haven't test fit this #13703 hitch on your Winnebago Micro Minnie but if you measure the frame of your RV and it's between 22 and 72 inches in overall width this would easily fit.

view full answer...

Answer 3

We will have a trailer hitch receiver that is able to be mounted to your 2021 Winnebago Micro Minnie 225RL, but you will need to determine the correct one. From the photos I saw it looks like this trailer does have a bumper and spare tire, so you…

view full answer...

Answer 4

We do offer a roof rack that will fit your 2015 GMC Savana van, as well as a cargo basket that is going to work on it. Let's start with the roof rack you'll need, which is a square bar rack made from Inno and consists of the following parts:…

view full answer...

Answer 5

Yes! I confirmed with Inno that the Inno Feet for Square Crossbars - Rain Gutters -5-1/2" #IN72FR and the Inno Square Crossbars - Steel - Black - 65" Long #INB165 are confirmed to fit you 2005 Chevy Express Van 3500.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...