Recommendation for Tire Chains on my 35x12.5x17 Sized Tires on a 2010 Jeep Wrangler Sport

Question

Question:

Im assuming these will fit 35x12.5x17 tires, 2010 Jeep Wrangler Sport? Thank You

asked by: Raymond S

0

Expert Reply:

According to my information # TC3231 from Titan Chain will fit the tires you have listed.

I would recommend using a Rubber Tire Chain Adjuster from Titan # TCOA2 for these snow chains to keep them secure and tight to your tire.

I have linked a video on this brand of chain to show you how they are mounted and the rubber piece is attached for your convenience. According to my information contrary to the video the chain you will receive is one ladder style not two.

expert reply by: Jackie C

0

Answer 1

For your Jeep tire chains on your 35x12.5x17 inch tires, we do not have any 7mm thick links, but we do have heavy duty chains with 5.6mm link thickness. I recommend the Pewag All Square Snow Tire Chains for Wide-Base and Dual Tires - 1 Pair #PWE3231S…

view full answer...

Answer 2

Here is a list of the tire chains we carry that will fit the 35x12.5-17 tires you have on your Jeep. Titan Chain Snow Tire Chains w/ Cams for Wide Base Tires - Ladder Pattern - V-Bar Link #TC3831CAM Titan Chain Snow Tire Chains for Wide Base Tires -…

view full answer...

Answer 3

Doesn't look like you'll need S compatible chains on your truck since the manual doesn't mention it and it looks like you have plenty of clearance on the truck tires/wheels. V-bar chains like the #TC3831CAM are designed to do the best in…

view full answer...

Answer 4

For the 35x12.5-18 size tires on your 2005 Ford F-150, the best option we have are the Glacier Twist-Link Snow Tire Chains #TC3231SCAM which has cam tighteners to assist with the tensioning. Unfortunately there are no self-tensioning systems…

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...