Pipe Mount Trailer Jack Recommendation to fit 2-1/2 inch Pipe Mount on Trailer
Question:
I need a pipe mount jack with a female pipe on the jack to fit a 2.5male pipe on my roller. Could you please recommend?
asked by: Donald J
Expert Reply:
The Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 7,000 lbs, item # BD198250, has a male pipe on the jack and a female receiver that welds to the trailer. This female receiver has an inside diameter of just over 2-1/2 inches to fit on the 2-1/2 inch male pipe welded to the jack. This jack utilizes a 5/8 inch pin to secure the jack to the trailer. When fully extended it is 31 inches from where it mounts to jack to the ground.
It sounds like this jack would work well for you, but without knowing more it's hard to say for certain. If nothing else the mount for this jack could easily get welded to your trailer.
Product Page this Question was Asked From
Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 7,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 6001 - 7000 lbs
- Sidewind Jack
- Swivel Jack
- 15 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 7,000 lbs
- Q&A: Mounting Ring Diameter for the BullDog Round, Pipe-Mount Swivel Jack # BD198250
- Video: Review of Bulldog Trailer Jack - Side Frame Mount Jack - BD198250
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Q&A: Pipe Mount Jack Recommendation to Attach to 2-1/2 inch Mount on Trailer
- Q&A: Trailer Jack Pipe Mount Upgrade From 3,000 lb Bulldog Swivel Jack
- Search Results: 198250
- Search Results: side crank jack
- Q&A: Bulldog Trailer Jack Recommendation for Trailer with 2-1/2 inch Pipe Mount on Trailer
- Shop: Replacement Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 2-1/2" - 5/8" Pin Hole
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 5,000 lbs
- Shop: Bulldog Replacement Pipe Mount for Swivel Jacks - 2-1/2" Female - Weld On - 5/8" Pull Pin
- Video: Bulldog Square Sidewind Swivel Jack Review
- Q&A: Capacity of Bulldog Round, Pipe-Mount Swivel Jack # BD198250
- Q&A: What Pipe-Mounted 7000-lb-Rated Jacks Work With Bulldog Weld-On Pipe Mount # BD003155
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 14-7/8" Travel - 2K
- Shop: Bulldog Square Swivel Jack w/ Round Pipe Mount - Sidewind - 15" Lift - 3,000 lbs
- Q&A: Distance From Center of Pipe Mount to Bottom of Foot On Bulldog Trailer Jack BD198250
- Shop: Vehicle Engine Heaters
- Search Results: bd178203
- Search Results: crown jack
- Search Results: bd198250
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Shop: Fifth Wheel Hitch
on Trailer Jack
