Will Fifth Wheel Trailer Steel King Pin Tripod Stabilizer Fit a Trailer with a Capture Plate

Question

Question:

I have a SuperGlide Hitch with a Pull Right Adapter Plate on the king pin. Can I use this to stabilize my trailer?

asked by: Paul P

0

Expert Reply:

Sounds like you have a capture plate on your trailer's pin box so that your Superglide will work. The Ultra Fab Tripod part # UF19-950001 would work just fine with the capture plate as it just fits around the king pin.

expert reply by: Jameson C

0

Answer 1

No, use of the Timbren suspension enhancements like the Timbren Rear Suspension Enhancement System #TDRTT1500 will not void your warranty. You are protected by the Federal Magnuson-Moss Warranty Act. This act says if something breaks on your…

view full answer...

Answer 2

Beautiful truck and travel trailer you have there! Airbag suspension enhancement is the best way to reduce rear sag and improve the handling of your truck when you are pulling a heavy load, such as your 40 foot Montana 5th wheel. You can then…

view full answer...

Answer 3

I do have an option for you but the glass on the Furrion RV Electric Fireplace isn't replaceable because Furrion does not offer any glass for this exact purpose. If you would like to try and find the glass elsewhere you're welcome to…

view full answer...

Answer 4

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 5

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 6

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 7

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Will Fifth Wheel Trailer Steel King Pin Tripod Stabilizer Fit a Trailer with a Capture Plate

Product Page this Question was Asked From

Continue Researching