Will Kodiak Hydraulic Tandem Brake Line Kit Work With Trail-Rite 21 Ft Boat Trailer

Question

Question:

I have a trail-rite tandem axle #5000 galv trailer #GB-21W-T4 . Will your all rubber kit #20TA-BLKIT work for my trailer?

asked by: Mike D

0

Expert Reply:

The Kodiak Hydraulic Brake Line Kit, part # 20TA-BLKIT would be a great fit for your Trail-rite trailer.

From my research I found your trailer is 21 ft 8 inches long and has tandem axles. The 20TA-BLKIT is 20 ft long and has all of the hydraulic lines and fittings needed to run your lines from the actuator to the brakes.

expert reply by: Jeffrey L

0

Answer 1

The Kodiak #20TA-BLKIT 20 foot brake line kit will work if the distance from the rear of the coupler to the front trailer axle is roughly 18 to 19 feet, as you'll need some slack for the swing-away coupler to move freely. having a little extra…

view full answer...

Answer 2

It is recommended to have brakes on both axles, but it isn't unheard of to just have brakes on one axle. What this means though is that you won't get as much stopping power and those brakes are going to wear down a lot quicker than they would…

view full answer...

Answer 3

The loom clamps that are included with the #20TA-BLKIT hydraulic brake line kit are zinc plated steel, not stainless. The zinc plating isn't as corrosion resistant as stainless would be, but it'll still offer some protection.

view full answer...

Answer 4

The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…

view full answer...

Answer 5

Having the slightly larger main feed line of 1/4 inch is a a great idea for plumbing up your triple axle trailer. We have the HydraStar kit part #HS496-153 which is designed for that. This kit uses 1/4 for the main feed line to the first tee fitting…

view full answer...

Answer 6

For brake lines, we have many sizes and they are either flexible rubber hoses like #HS496-252 or fixed lines like #T4829900. I've linked the page to all the components and kits we carry.

view full answer...

Answer 7

The brake line kit that would be best for you will depend the number of brake assemblies, the length of the trailer and whether the brakes are drum or disc. If you have a single axle trailer using drum or disc brakes, and the distance between the…

view full answer...

Answer 8

The #20TA-BLKIT brake line kit you referenced is indeed compatible with the #AKUBRK-35-D Hydraulic Brake assemblies you'd looked at, the line kit is compatible with bolt disc and drum brake systems. The brake assemblies will be compatible with…

view full answer...

Answer 9

The majority of brake line installations we do in our shop match the first method you have in the photo, labeled "Branch". We also prefer to use rubber hoses as they are easier to work with and there won't be an issue if you end up with…

view full answer...

Answer 10

The Kodiak Hydraulic Brake Line Kit #18TA-BLKIT will work great for you, however I'd personally prefer to have some excess length just incase, so the Kodiak Hydraulic Brake Line Kit #20TA-BLKIT is what I'd go with. Both of these kits have a…

view full answer...

Answer 11

Yes, the Dacromet/Stainless finish on the 10" Kodiak Disc Brakes #KOD67FR is arguably the best for boat trailers since it's the most resistant to rust and corrosion, although it's still a good idea to hose down your trailer with clean…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Will Kodiak Hydraulic Tandem Brake Line Kit Work With Trail-Rite 21 Ft Boat Trailer

Product Page this Question was Asked From

Continue Researching