Hitch Comparison for a 2012 Hyundai Elantra Sedan
Question:
You have two trailer hitches listed for a 2012 Hyundai Elantra, the Curt Class I Round Tube Receiver Hitch - 2012 Hyundai Elantra and the Draw-Tite Class I Sport Frame Receiver Hitch - 2012 Hyundai Elantra. The mounts look different, will both fit my car or do I need one over the other?
asked by: Christopher C
Expert Reply:
For your 2012 Hyuandai Elantra Sedan you do have two options for a trailer hitch.
The Draw Tite Hitch part # 24902 and the Curt part # C11303.
Both have similar buy slightly different designs. I would go with the Draw Tite hitch as it has a slightly higher customer rating a slightly easier install rating as well. I attached an install video for you to check out as well.
For trailer wiring you would need the #118532, # ball mount 3594, 1-7/8 inch hitch ball # 19256, or 2 inch hitch ball # 19258.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Roof Rack and Cargo Basket Recommendation for 2015 Honda CR-V with Naked Roof
- Q&A: Will the Kuat Sherpa 2.0 2-Bike Platform Rack Block a Rear Backup Camera
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Can Sumo Springs for Motorhome Be Installed Without Removing Rear Wheel
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: Tip for Difficult to Engage Tool of Rhino Rack Pioneer Platform 2022 Toyota RAV4
- Q&A: How To Shift A 2021 Jeep Wrangler Transfer Case Into Neutral To Flat Tow
- Q&A: Replacement Grease Seal for AF3531G
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How Much Does a Boat and Trailer Weigh?
- Article: How to Choose a Bike Rack for a Sedan or Hatchback
- Article: Which Hitches are Made in the USA
- Article: How to Bleed Your Trailer Surge Brakes
- Article: What is Overlanding? How to Start your Overlanding Journey