Replacement Trailer Taillight Assembly Recommendation for 3348 Capsule that Has Blown on Trailer

Question

Question:

My units calls for #3348 Replacement for boat trailer tail lights. Is this a correct current product number. Please advise asap if new product replacement is required. Do not require LED. Thank you.

asked by: Al

0

Expert Reply:

The 3348 is a Wesbar capsule that is no longer available. What you would need instead is the part # 403026 for the left hand side and/or part # 403076 for the right hand side.

expert reply by: Jameson C

0

Answer 1

The correct replacement grease seal for the AD2527E you listed is the part #168233.

view full answer...

Answer 2

I have a few things for you to check when it comes to not being able to pair your iPhone with the Curt Echo #C51180. The first thing to do is make sure that you're pairing your phone with the Echo through the app. If you paired it through…

view full answer...

Answer 3

In some cases trailer lighting will ground through the hitch ball but that's typically only if the actual ground circuit is insufficient. This is not an ideal setup. It needs to ground through the wiring of the trailer harness. You can test this…

view full answer...

Answer 4

The number 8752 that you referenced doesn't match up with any seal numbers that we carry, but there is a way to determine what replacement seal you would need. You will want to measure where the seal rides on your axle spindle with a dial or…

view full answer...

Answer 5

Did you have a 4-pin connector that had 5 wires or was it a 5-pin connector? There is a big difference since you normally see a 5-pin connector on a boat trailer with the 5th pin used for an electric reverse lockout solenoid on a brake actuating…

view full answer...

Answer 6

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable. If your capsule is sealed, then your best option is to replace the lights with new lights like part #403026 and #403076.…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Replacement Trailer Taillight Assembly Recommendation for 3348 Capsule that Has Blown on Trailer

Featured Help Information

Miscellaneous Media

Continue Researching