RV Ladder Recommendation for a 2001 Coachmen Mirada

Question

Question:

What ladder replacement would be recommended for a 2001 coachmen mirada 300qb

asked by: Chuck

0

Expert Reply:

RV ladder # LA-401 may be the best option for you since it can be trimmed to length needed (it starts out at 99-1/2 inches tall) and will fit straight or curved roofs and bodies. I have included a picture showing various measurements of this ladder so you can determine if it is a fit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

There is a couple of way to determine which wheel bearings and grease seals you will be needed for a trailer axle. First, checking the numbers on the wheel bearings and seal will allow you to select the correct parts for your axle. However, in some…

view full answer...

Answer 2

I spoke with my contact at Dexter regarding the axle on your trailer. This is a 6,000 pound axle that uses inner bearing #25580 and outer bearing #15123. For a complete bearing kit, you can use #BK3-100. This will include the correct inner and outer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

RV Ladder Recommendation for a 2001 Coachmen Mirada

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching