Will a Fold Away Coupler Work on a 2002 Blazer Bass Boat Trailer with Hydraulic Surge Brakes
Question:
Does this swing away tongue weld on coupler work if you have surge brakes? If so what other parts would I need to complete the installation?
asked by: Michael C
Expert Reply:
Yes, the Fulton Fold-Away Hinge Kit for 3 x 3 inch Trailer Tongue - Weld-On, item # FHDPW330300, will work on a trailer with surge breaks.
You will need to determine the length of the coupler that will be in front of the fold away to select the appropriate length of flexible hydraulic brake line to allow the foldaway to fold without damaging the brake line. We have several lengths of flexible brake line available for this.
Titan Hydraulic Brake Line with Fittings - 12-27/32 inches Long, item # T0777300
Titan Hydraulic Brake Line with Fittings - 18-25/32 inches Long, item # T0776500
Titan Hydraulic Brake Line with Fittings - 25 inches Long, item # T0980100
You will then need to shorten the existing brake line by coiling it inside the stationary part of the tongue (always coil from the top down not bottom up or sideways) or by cutting the line reinstalling the fitting, in the correct direction, on the line and double flaring the end of the cut brake line.
Products Referenced in This Question
Dexter Hydraulic Brake Line with Fittings - 18-25/32" Long
- Accessories and Parts
- Brake Actuator
- Trailer Brakes
- Disc Brakes
- Hydraulic Drum Brakes
- 18-25/32 Inch Long
- Brake Lines
- Flexible Brake Hose
- Brake Line Components
- Dexter
more information >
Dexter Hydraulic Brake Line with Fittings - 13" Long
- Accessories and Parts
- Brake Actuator
- Trailer Brakes
- Disc Brakes
- Hydraulic Drum Brakes
- 13 Inch Long
- Brake Lines
- Flexible Brake Hose
- Brake Line Components
- Dexter
more information >
Dexter Hydraulic Brake Line with Fittings - 25" Long
- Accessories and Parts
- Brake Actuator
- Trailer Brakes
- Disc Brakes
- Hydraulic Drum Brakes
- 25 Inch Long
- Brake Lines
- Flexible Brake Hose
- Brake Line Components
- Dexter
more information >
Product Page this Question was Asked From
Fulton Fold-Away Coupler Hinge Kit for 3" x 3" Trailer Tongue - Weld On - Up to 5,000 lbs
- Folding Trailer Tongue
- Coupler Hinge Kit
- Up to 48 Inch Long
- Weld-On
- 5000 lbs GTW
- 3 x 3 Inch Tongue
- Fulton
more information >
Continue Researching
- Q&A: Solution for Atwood Surge Brake Coupler Needing Replacement Parts
- Article: Pintle-Hitches
- Q&A: Factory Brake Wiring Harness Location on 2012 Chevy Silverado
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: Big Truck Big RV
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: How to Determine the Correct Replacement Bearings for a Trailer
- Q&A: Does The etrailer Invisible Base Plate Kit # e86YR Need An Adapter For A Blue Ox Aventa II Tow Bar
- Article: Trailer Wiring Diagrams
- Q&A: Hitch Extension for Towing a Boat on a Truck with an In-Bed Truck Camper
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Q&A: Can I Use Both the 7-Way and 4-Way Connectors at the Same Time on a 2015 Chevrolet Silverado
- Article: Trailer Tire Sizing
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)