What Grease Seal Do I Need for Boat Trailer That Uses LM67048 and 25580 Bearings

Question

Question:

Would it be possible to tell me which grease seal to use with a LM67048 and a 25580 bearing on a boat trailer?

asked by: Anthony K

0

Expert Reply:

With bearings numbers of LM67048 and 25580, we offer two different grease seals, # RG06-090 which has an inner diameter of 2.125 inches and # RG06-070 which has an inner diameter of 2.25 inches.

To determine which is the correct seal for your boat trailer, you will need to use a digital caliper to measure the portion of your spindle where the grease seal rides. I have attached a photo to illustrate this area.

expert reply by: Leah S

0

click to enlarge

Answer 1

You are going to need to measure your current spindle to determine whether or not you need a 2-1/8 inch seal like #RG06-090 or if you need a 2-1/4 inch seal like #RG06-070. You will need to take the measurement of the spindle where the grease seal…

view full answer...

Answer 2

There are two seal options available for a hub that has the two bearing numbers you mentioned LM67048 and 25580. If your spindle measures 2.125 inches where the seal rides you need the 10-10 #RG06-090. If instead you have an inner diameter of 2.25…

view full answer...

Answer 3

The difference between the single lip and double lip seals is that the double lip grease seal will have two rubber lips that are in contact with the spindle. The double lip grease seals are usually used in marine applications to give a better seal…

view full answer...

Answer 4

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 5

The correct grease seal for your axle is #RG06-070. I've attached a video review for you to take a look at.

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

What Grease Seal Do I Need for Boat Trailer That Uses LM67048 and 25580 Bearings

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching