Replacement Clevis Pin for Fulton Fold-Away Coupler Hinge Kit

Question

Question:

I need a 5/8inch x 3 3/4inch usable length hitch clevis pin. Same as pin for Fulton swing away tongue

asked by: Glenn S

0

Expert Reply:

We offer two clevis pins that come close to the dimension you're looking for.

The # MT70053 measures 5/8 of an inch in diameter and 3-5/8 inches long. Part # 586H measures 5/8 by 6 inches long.

If you were looking for a replacement clevis pin for the Fulton folding trailer tongue, we only have one size, the pin for a 3x5 tongue, # F500336.

expert reply by: Mike L

0

Answer 1

We offer three 9/16-inch diameter pull pins including the Bulldog #BD500243 which has a usable length of 2-1/2-inches. Bulldog part #BD500338 has a usable length of 2-3/4-inches and part #TJP-PN916 has a usable length of 3-1/2-inches, with…

view full answer...

Answer 2

I do have several replacement parts available for the RAM Trailer Jack part #TJD-7000S but not an all inclusive rebuild kit. Instead you will need to select from the components listed below and repair the jack as needed. The most common fault on the…

view full answer...

Answer 3

For the leg of your Trails West Gooseneck Trailer, the Replacement Pin options depend on the diameter of your jack's pin. There are options that have chains or springs depending on that pin diameter. If you have a 5/8 inch pin diameter then…

view full answer...

Answer 4

We have the Bearing Buddy Bearing Protectors #BB1968SS that fit a hub bore of 1.968 which is likely the size you have. The measurement may be slightly off based on the outside temperature as steel can expand and contract based on temperature.

view full answer...

Answer 5

The only trailer component that determines the speed rating of the trailer is the tires. All you have to do is simply replace your current tires with one that is rated for highway use, like the Kenda Loadstar #AM3S120 that you referenced, and you are…

view full answer...

Answer 6

Bearing Buddy pumps grease into the center of the hub all the way back to the grease seal. A double lip seal should be used to prevent grease from blowing out the seal when added. When the hub and seals and bearings are first assembled, they should…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, it is certainly possible to remove the pivot bolt from the Fulton Fold-Away Coupler Hinge Kit #FHDPW330300 to enable you to separate the two halves of the assembly. Both the pivot pin and pivot bolt are included with this assembly and it is…

view full answer...

Answer 9

A 5/8" pin is the most common diameter used for a swing away tongue. There are different length pins for different height frames. The only one we currently carry is for a 5" tall frame, for this you will use a Pin #F500336. Be sure to…

view full answer...

Answer 10

We were able to find out the dimensions for you of the Fulton Fold-Away Coupler Hinge Rubber Plug Kit #F500705. Using digital calipers it measured 0.423 inches tall and its round base has a diameter that measured 0.426". These are designed to…

view full answer...

Answer 11

The Replacement Pivot Pin part #F500336 is not rated like a bolt grade. As long as the hinge kit you use is rated for the weight of the trailer, you'd be fine.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Clevis Pin for Fulton Fold-Away Coupler Hinge Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching