Short Trailer A-Frame Toolbox Options

Question

Question:

no more than 33 inches in the back 20 inches in the front 11 inches tall 14 inches front to back. better if it was not 14 inches like 10 inches front to back

asked by: Judd S

0

Expert Reply:

The closest match we have to the dimensions you are looking for in an A-Frame toolbox is going to be # 350980. It measures 30 inches across at the back, 17-1/2 across at the front, 14 inches front to back, and 14 inches tall.

Everything else is going to be much wider (front to back) or much taller than what you are looking for. I have included a link to all of the A-Frame toolboxes we carry for you.

expert reply by: Michael H

0

Answer 1

The RC Manufacturing T-Series Trailer Tongue Tool Box part #350980 has a black powder coated finish. Powder coated finishes are usually not as smooth as painted finishes. They are however much more durable than paint. If the tool box was painted it…

view full answer...

Answer 2

There isn't one set in stone way to install the RC Manufacturing T-Series Trailer Tongue Toolbox #350980 but typically people will drill holes through the bottom of the box and into the trailer frame below it and then run carriage bolts through…

view full answer...

Answer 3

The Dee Zee Specialty tool box #DZ6535P should work as a tongue tool box for your trailer dimensions. The overall dimensions of this tool box are: 35 inches long by 14 inches wide by 13 inches tall. Please check these measurements with your trailer…

view full answer...

Answer 4

The A-Frame Trailer Tongue Toolbox #350980 will fit on an A-frame trailer where the frame measures 17-1/2 inches edge to edge and go back from that location 15-1/2 inches along the frame. This will let you know if there is room for your spare if…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...