What is the Correct Torque Specification for Trailer Wheel

Question

Question:

what would the torque specification be for this size wheel

asked by: Paul S

0

Expert Reply:

Torque specs for trailer and vehicle wheels are based on the size of the wheel stud, the type of lug nut, and the material the wheel is made of, steel or aluminum. For example, the linked chart shows you the varying torque values for a range of larger wheel sizes based on these factors.

Without knowing more about your hubs and wheels I cannot give you a specific torque value, but it is likely that that spec would fall into the range of 75-80-ft-lbs.

expert reply by: Adam R

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Thank you for your many purchases from etrailer, including your recent purchase of two of the Andersen Camper Wheel Chock and Leveler #AM3604. The 4-inch maximum height of this leveler is not going to provide enough lift to get the bad tire of a…

view full answer...

Answer 3

It sounds like you're looking for the torque specs for the lug nuts on a 6,000 pound axle. For a hub with 1/2 inch studs, 90 to 95 foot-pounds is standard.

view full answer...

Answer 4

For a trailer tire you have to go with ST rated tires. The tires you have currently are for passenger vehicles and that is what the P in front of the size means. I would strongly recommend you upgrade your tires as soon as possible. The closest size…

view full answer...

Answer 5

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 6

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 7

That really depends on the material of your rim and the diameter of your wheel studs. If you have a steel wheel with a 1/2 inch stud you would use 90-120 ft/lbs. Steel with 9/16 inch stud 120-140 ft/lbs. Aluminum with 1/2 inch stud 90-100 ft/lbs.…

view full answer...

Answer 8

The ST205/75D15 tire that you've currently got are the same size as a tire like the Karrier ST205/75R15 Radial Trailer Tire - Load Range C #AM10244, but the difference is that your D15 tire is a bias-ply tire where the Kenda Karrier R15 tires are…

view full answer...

Answer 9

Tire designations ST205/75D14 and ST205/75R14 are both for special trailer tires with a 205mm width, 75-percent aspect ratio and that fit a 14-inch wheel. The difference between them is the tire's type of construction. The ST205/75D14 tire is a…

view full answer...

Answer 10

The best tire for your trailer in the same size that you have is the part #AM10245. This is the highest capacity tire we offer in that size. It is a Load Range D with 2,150 lbs at 65 psi capacity. Your current tire is a bias-ply. I can tell by the…

view full answer...

Answer 11

Based on the tire sizes you listed you went from a radial tire to a bias ply tire of the same size. As long as all of the tires on your trailer are of the same construction you would be just fine. The main difference between a radial ply and a bias…

view full answer...

Answer 12

I have attached a chart for you to take a look at that includes the lug nut torque specifications. If your wheel uses 1/2 inch lug nuts or wheel bolts like the 12 Inch Steel Spoke Trailer Wheel #AM20124 referenced in your question, you will torque…

view full answer...

What is the Correct Torque Specification for Trailer Wheel

Product Page this Question was Asked From

Continue Researching