Replacement A-Frame Coupler That Measures 11 Inches At Widest Point

Question

Question:

Which coupler do I need, # CA5400?

asked by: Scott

0

Expert Reply:

The Redline 14K capacity A-Frame Coupler, part # CA5400 you referred to measures 11 inches wide at its widest point, like the A-Frame coupler you showed in the photo you provided (thanks for the photo, by the way.)

The # CA5400 is compatible with 2-5/16 inch trailer balls, and would make an excellent replacement for your current corroded A-Frame coupler.

expert reply by: Mike L

0

click to enlarge

Answer 1

The etrailer #CA-5400-B weld-on coupler you were looking at would be a great replacement for your current Parker Performance A-frame coupler. This coupler has a 2-5/16 inch ball and a weight capacity of 14,000lbs. I have linked this product to this…

view full answer...

Answer 2

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 3

Welding a mounting flange, possible item #4-35, is a very precise installation. The flanges need to be installed square and concentric to the hub and drum assembly and each other. If the flange is installed incorrectly rapid brake lining wear,…

view full answer...

Answer 4

I spoke to my contact at Dexter Axle and was able to determine that you have a 3,500 lb axle with 80" spring center and 94" hub face measurement which means the correct replacement for you will be the Dexter Trailer Axle Beam with E-Z Lube…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Replacement A-Frame Coupler That Measures 11 Inches At Widest Point

Product Page this Question was Asked From

Continue Researching