Replacement Bearing For Bulldog 5,000 Lb Trailer Jack
Question:
I have a hand crank 5000lb Bulldog trailer lift for the tongue of my dump trailer and it recently got very difficult to operate. I pulled it apart to see if there was something I could grease and it appears to have had a bearing at the top that is totally destroyedshards of metal and balls mixed with the grease. I do not see anything in your parts listed that seems similar and was hoping it was a replaceable part so I dont have to cut that one off and weld on a new one
asked by: Tom S
Expert Reply:
We may have the bearing you are looking for that will work with your 5,000 lb Bulldog trailer jack.
The replacement bearing we have is part # BD500223. The bearing has an inner diameter of approximately 0.525 inches, and outer diameter of 1.25 inches, and it is 0.43 inches thick. I have attached a photo of this bearing with the dimensions noted you can check out. This also includes the washer. This bearing will fit round Bulldog jacks with a 5,000 weight capacity and can be used for Bulldog series 170 jacks.
If you find that the bearing is not the part that will work and you want to replace the jack, you can take a look at the attached product page for the trailer jacks we offer that may work for you.
Product Page this Question was Asked From
Replacement Thrust Bearing for Bulldog Round Tube Trailer Jacks with 5,000-lb Capacity
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Bearings
- Thrust Bearings
- Bulldog
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Trailer Wiring Diagrams
- Q&A: Wire Colors and Functions of Hopkins 7-Way Molded Trailer Wire Connector
- Shop: Replacement Thrust Bearing for Bulldog Round Tube Trailer Jacks with 5,000-lb Capacity
- Shop: Steel Mod Silver Trailer Wheel - 15" x 5" Rim - 5 on 4-3/4
- Shop: Replacement Bearing for etrailer and Ram Square Jacks - 7,000 lbs
- Shop: Replacement Bearing for etrailer and Ram Round, Topwind Jacks - 2,000 lbs and 5,000 lbs
- Shop: Replacement Bearing for etrailer and Ram Square Jacks - 10,000 lbs
- Shop: Replacement Bearing for etrailer and Ram Round Swivel Marine Jacks
- Video: Bulldog Jacks Replacement Thrust Bearing Review
- Search Results: bulldog jack bearing
- Shop: Vehicle Cargo Control
- Video: Rebuilding the etrailer and Ram Square Jacks
- Q&A: Do You Grease Inside Of Dexter Nev-R-Lube Hub Or On The Spindle Before Installing The Hub?
- Q&A: How Tight Should Trailer Bearings Be When Installing on a Spindle
- Q&A: What is the Torque Spec of the Spindle Nut on a Dexter E-Z Lube Axle
- Shop: Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Search Results: trailer brake controller
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Choosing the Right Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Video: Choosing the Right Brake Controller
- Shop: Trailer Wiring
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Search Results: trailer hitch
- Search Results: safety chains
on Accessories and Parts
