Installing a Curt Trailer Hitch on a 2015 Ford Focus SE
Question:
need expert advice on installing curt 11158 hitch to a 2015 ford focus
asked by: Jack W
Expert Reply:
I will be happy to help. What kind of trouble are you having? The Curt trailer hitch # C11158 will only fit sedan and hatchback models that are NOT an ST trim or an electric model. I have included a link to the installation instructions for you to view.
The hitch pretty much just bolts into place. I have included a link to a video showing installation for you on an older model but the installation will be nearly identical on your 2015. I have also included a link to a video on the fishwire technique and a link to our help article of installation tips.
If you plan on doing some towing the correct ball mount is # C45521. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier you have to make sure the accessory is rated for use on a Class I hitch. Also Curt says you need to use stabilization strap # 18050 for any non-trailer loads including bike racks or cargo carriers.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Printable Trailer Bolt Hole Pattern Template
- Article: Trailer Hitch Receiver Sizes
- Article: Roadmaster Vehicle Specific Base Plates
- Article: Flat Towing Package for 2008-2011 Honda CR-V
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: Will Curt T-Connector Fit 2015 Ford Focus ST Hatchback
- Article: What Do I Need To Tow A Trailer?
- Q&A: Trailer Wiring Harness Recommendation for a 2014 Ford Focus ST Hatchback
- Q&A: How Can I Get Additional Trailer Wiring Signals at the Rear of my Durango
- Q&A: How Does Hitch Tongue Weight Rating Affect Use of a Motorcycle Carrier on a Toyota Sienna
- Q&A: Curt Echo Brake Controller for 2023 Jeep Grand Cherokee 4xe
- Q&A: How To Wire Up Hopkins Engager Push-To-Test Trailer Breakaway Kit