Recommended Suspension Enhancement for 2014 Ram 1500 Crew Cab Outdoorsman

Question

Question:

I am interested in the Timbren suspension enhancement. I have a 2014 Dodge Ram 1500 Outdoorsman Crew Cab. On their website it stated that these will not fit my veh. Do you know if in fact they will fit or is there another system that you recommend. I prefer not to use airbags. Thank you.

asked by: Anthony S

0

Expert Reply:

I checked with Timbren and my contact there said the Timbren Vehicle Suspension, part # TDR1500DQ, that you referenced are indeed a fit for the Outdoorsman models of the 2014 Ram 1500 Crew Cab. To install part # TDR1500DQ, they will snap into place just like the old bump stops. They are pressed into the cup like you see in the video, linked for reference. I have also included a link to the instructions.

You will also want to remember that by adding this suspension system you will not be increasing the weight capacity of your vehicle.

expert reply by: Chris O

0

Answer 1

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 2

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 3

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 4

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Recommended Suspension Enhancement for 2014 Ram 1500 Crew Cab Outdoorsman

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching