Installation Instructions For Base of Thule TracRac Contractor Truck Bed Ladder Rack

Question

Question:

I didnt get the instructions with the racks i figured out how to assemble them but not sure how to mount them with the bolts it came with do you have a diagram?

asked by: JIB

0

Expert Reply:

I'm attaching a photo of how the base of the Thule TracRac Contractor Truck Bed Ladder Rack # TH14750 gets installed on the truck bed for you to check out.

expert reply by: Jameson C

0

Base Installation Diagram for Thule TracRac Contractor Truck Bed Ladder Rack
(click to enlarge)

Answer 1

For a great ladder rack that fits with your BAKFlip MX4 on your 2021 Silverado 1500 with a 5'8" bed, I recommend the Adarac Pro Series Custom Truck Bed Ladder Rack #A4002965. Since the BAKFlip MX4 completely installs within the bed…

view full answer...

Answer 2

From the floor of your truck bed to the top of the Thule TracRac Contractor Truck Bed Ladder Rack #TH14750 crossbar will measure 47". If you check out the linked you'll see that to the bottom of the crossbar is 45-1/2", and…

view full answer...

Answer 3

The Thule TracRac #TH14750 is a universal type of product so you can use it in your Chevy Silverado 1500 with 5-1/2 foot bed.

view full answer...

Answer 4

Usually ladder racks use the inside edge of the top of the bed site to attach to the vehicle, but luckily there are exceptions to that. The Thule TracRac SR is typically compatible with tonneau covers that mount to the inside edges of the truck…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Installation Instructions For Base of Thule TracRac Contractor Truck Bed Ladder Rack

Product Page this Question was Asked From

Continue Researching