What Material is the Convert-A-Ball Interchangeable Ball Set # 906B Made Of

Question

Question:

IS the nut and cotter pin stainless? Are these made in the USA?

asked by: Owen M

1

Helpful Expert Reply:

The nut and cotter pin of the Convert-A-Ball Interchangeable Ball Set # 906B are zinc coated to prevent corrosion. Everything else is stainless steel and this is made in the USA.

I attached a review video for you to check out as well.

expert reply by: Jameson C

1

Answer 1

If you only have the nut and a washer but no cotter pin or retaining type washer on the end then that isn't correct and you want to get a piece to help prevent that nut from backing off. If you have a setup like the Spindle Nut Kit for EZ Lube…

view full answer...

Answer 2

Yes, the Washer Spindle Tongue part #165863 will work with 7/8" diameter spindles. If you also need the castle nut and cotter pin as well we have these available as part #165931 and part #165649.

view full answer...

Answer 3

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 4

Equalizer bolts, like the TruRyde Wet Equalizer Bolt, #TRFA71063, should be torqued to yield. Equalizer bolts are not given a specific torque rating because they should allow some movement of the equalizer. If they are torqued down too tight, the…

view full answer...

Answer 5

For the middle equalizer bolt and nut that fits the Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs #APTT6SE you need the Equalizer Bolt with Cotter Pin and Castle Nut - 7/8" Diameter #166078. If you would like to upgrade to a wet…

view full answer...

Answer 6

I attached a picture of the castle nut and nut retainer that comes with the trailer axle part #20440I-EZ-60 that you referenced. This does not come with the cotter pin setup like you mentioned.

view full answer...

Answer 7

The correct replacement castle nut, cotter pin, and washer for a trailer with 1" round spindle is as follows: Castle Nut part #165686, Cotter Pin part #165649, and Washer part #SW1000. Unfortunately, we can't cross-reference trailer mfg.…

view full answer...

Answer 8

There is not an exact torque specification to pre-load the bearings on a mobile home axle. The spindle nut will need to be tightened by hand until finger tight and then turned another 1/4 of a turn with a wrench. This will be around 15 ft-lbs but you…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

What Material is the Convert-A-Ball Interchangeable Ball Set # 906B Made Of

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching