Removing Seized Hardware in a Semi Trailer Floor

Question

Question:

I have some old semi-trailer flooring that I am trying to remove from the metal support I-beam braces. The bit size is a T40 Star Bit, I used a low quality bit and the points on the bit just bent and snapped off. Do you have this size bit? Have you had previous customers have any success removing these old bolts from semi-trailer floors?

asked by: Mike

0

Expert Reply:

We do not have that particular size bit but I can tell you that you will likely need to spray some penetrating oil on the old hardware and let it soak for at least 15 minutes. This will help to break up the seized hardware.

If you still have trouble after that then the only other option would be to drill out the hardware.

expert reply by: Michael H

0

Answer 1

The correct set of replacement brake assemblies for your AxleTek 12 inch assemblies is the kit part #AKEBRK-7-SA that you referenced. This kit is a pair of left and right assemblies that are an exact match to what you have that are also self…

view full answer...

Answer 2

If the screws part #TFX250ACQ are breaking that would indicate that they are corroded and seized up in the metal they are attaching to. So what you could do is take some spray lube to them where they attach to the metal and let that soak to see if…

view full answer...

Answer 3

The differences from trailer wheels, like the Dexstar Conventional Steel Wheel with Offset #AM20504 that you referenced, and vehicle wheels, like GM OEM wheels, can vary based on a lot of things. Trailer wheels are specifically designed to be used…

view full answer...

Answer 4

So you have 14 inch rim that has a 5 on 4-1/2 inch bolt pattern and are looking to go to a 15 inch rim. For that you would want the part #AM32424 as it has a ST205/75R15 tire mounted to it which has a 1,820 lbs at 50 psi capacity. The dimensions of…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Removing Seized Hardware in a Semi Trailer Floor

Product Page this Question was Asked From

Continue Researching