Difference In Mounting Hole Dimensions Between # RM-032 And # RM-033

Question

Question:

Does the RM-032 and RM-033 the same distance for the mounting holes? Is it 28 1/2 inch center to center between the mounting holes? Thanks a lot.

asked by: Marco S

0

Expert Reply:

The distance between the mounting holes center to center on part # RM-032 is 28-1/2 inches.

For part # RM-033, the distance from outside to outside of the bolt holes is 25-1/2 inches.

expert reply by: Jeffrey L

0

Answer 1

The width between the two tabs (as described in your photo) on the brackets of the #BX88230 Blue Ox Universal Adapter Tabs is just a hair over over 5/8 inches. I confirmed this with my contact at Blue Ox. These tabs are designed to accept the triple…

view full answer...

Answer 2

The Blue Ox Acclaim Tow Bar #BX4330 that you referenced can be used with base plate kits that are between 23 and 30 inches apart.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Difference In Mounting Hole Dimensions Between # RM-032 And # RM-033

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching